BILLIG FRAKT till Sverige - från 90 SEK
LÄS MER
BILLIG FRAKT till Sverige - från 90 SEK
LÄS MER
Logga in
Cutting and engraving - allows to cut and engrave on various materials such as wood, cardboard, rubber, paper, textiles, leather, plastic, balsa, plywood, and many others as well as a mark on stainless steel, titanium and low heat conductance type of steel. For more check Manuals and Articles section.
Factory set lens - the laser head is shipped the High-Resolution Triplet lens installed and adjusted to focus at 60.0 mm (measured from the front-face surface of the laser head to engraving plane). This focal distance has a well-optimized focal spot size which is suitable for many engraving and cutting applications. This is the best-optimized focus distance to start with!
Input signals versatility - build in driver allows accepting a variety of signals 0 - 5 V analog signal and 0 - 5 V, 0 - 10 V or 0 - 24 V for PWM/TTL signal.
Driver built-in inside the laser head - Opt Lasers is the first company who integrated the laser diode driver directly into the laser head. A short connection between the laser diode and a driver ensures better protection for a diode, possibility of high-frequency current modulation as well as eliminates inductance effects during the switch-on.
Accepts a wide range of power supplies - 12 - 24 V, an integrated high-efficiency DC-DC converter is adjusting the input voltage to proper diode compliance voltage. This reduces the amount of heat generated and ensures over-voltage protection.
No additional cooling required - a dedicated shape of the laser heads provides the best possible cooling method for a 6 W laser diode. Many prototypes have been made to find the best solution for cooling the laser diode. The current design allows the laser head to warm up only by 2 - 3 degrees Celsius after a whole hour of constant work at full power.
Two types of the lens included - The High-Resolution Triplet Lens with lens adjuster has a relatively long effective focal length (EFL) of 8 mm, which allows it to focus laser light to a small spot. All 6 lens surfaces are coated with anti-reflection (AR) coating centered at 450 nm. It is usually preferred for engraving a thinner line, cutting a thicker material due to the reduced convergence and divergence, or when a long distance between the laser head and the plane of the object to be engraved is necessary.
High-Efficiency Mounted Aspheric Lens is designed to obtain as much as possible power from the laser diode. Its short effective focal length (EFL) of 4 mm makes a variety of working distances possible but makes the focus spot almost twice bigger compared to Triplet Lens. This lens should be used for engraving thicker lines on wood or plastic. This type of lens is used without the lens adjuster since they need to be mounted closer to the laser diode.
Strongest fan available on a market in its size - cooling is not the only thing that a fan is doing - 43 m3 of air per hour (25 CFM) makes a great smoke removal system, additionally, the fan has 70000 hours life expectancy.
OEM customization available for of 3D printer and CNC machine companies
Compatible with accessories for ease of use - ease of work is very important to us. As well as safety. Many accessories we produce are high quality, made on CNC machine parts which make the work easy and safe. Please check out the accessories we prepared for the PLH3D series.
The laser head has two separate controls.
Modulation Input #1 accepts 0 - 5 V or 0 - 10 V (with additional 4,2 k ohm resistor in series) for analog power modulation
Modulation Input #2 accepts 0 - 5 V, 0 - 10 V or 0 - 24 V for TTL/PWM and turns on the laser when the voltage exceeds 2.5 V.
10V Analog Signal input connection (X-Carve, CS-Lab, and other machines)
In order to connect 0-10 V analog signal to the Modulation Input #1 it is needed to add a 4,2 k ohm resistor in series:
Important: The laser head should be powered from a high-quality power supply without anything else connected. Please note: connecting the laser head to the same power supply unit as a stepper motor or any other high-impedance equipment is not recommended. Doing so may cause damage to the laser diode.
- High power and high-frequency current laser diode driver
- Maximum output current A
- Input voltage 12 - 24 V
- Input current max 2 A
- Integrated microcontroller for temp. measurement and soft-start
- Thermal Protection - 45 degrees
- Soft start for diode protection.
- Laser Diode ESD protection
- Laser Diode reverse voltage protection
- Overcurrent protection
- Compact Size and >90% efficiency
- CW Mode and Input Control Mode.
- PWM/TTL and Analog inputs
- Modulation Bandwich 0 - 30 kHz
Opt Lasers is a laser diode drivers manufacturer. Thanks to our experience building over a few years we created a very high-efficiency driver with low power consumption and low heat production. Additionally, it is the fastest dedicated laser head driver available on a market accepting signals up to 30 kHz. Using 6W laser with high speed is no longer a problem while engraving small details or making small radius turns because the driver is able to read all needed signals.
CNC controllers are able to send modulation signals with great speed so 50 kHz is not a problem to them. This is why a high-speed driver is a must in such a device. The driver is able to read 30 000 instructions every second what creates great precision and resolution in terms of power control. Also, maximum driver current is 6 A so using it with 3 - 4 A value ensures offset and long lifetime of a driver.
The PLH3D 6W incorporates a thermal protection system that protects the laser diode from overheating to maintain its lifetime. The unit is designed to automatically shut off when the housing temperature exceeds 47 C. The analog input is protected by a 5V Zener diode in a case on occasion there appears the voltage higher than 5 V. Despite everything, this input should not be used with higher voltages due to a risk of damage. The laser diode is protected via a Schottky diode, which protects it from a reverse voltage and ESD. In addition, the integrated driver is fully covered to protect it from metal chips in a CNC machine environment.
The focus distance can be quickly set or changed via the included lens adjuster (no additional tools). The driver of the unit is integrated directly on the laser head. This greatly increases the maximum modulation frequency and allows longer cables to be used.
Besides the standard functionality, the small beam spot allows the possibility of using this product for rapid PCB prototyping. This is done by illuminating the copper layer of plates after a photosensitive paste is applied.
This lightweight 220 g (7.8 oz) laser head requires no additional cooling. The body acts as a heatsink, and the fan design allows it to function as an air nozzle protecting the lens from smoke, while also cooling the laser head. Performing tests on several prototype designs allowed us to optimize the heatsink’s shape and enable efficient cooling while maintaining the module’s notably small form factor.
The laser head allows engraving or cutting of materials such as wood, stainless steel, paper, leather, cardboard, and many others. For materials that generate smoke when engraved or cut, we offer an optional nozzle that is attachable to the front of the unit via magnets built into the laser head (see accessories).
For bulk orders, the PLH3D series can be customized to all customers' needs. We can add customers' logos and all possible additional features. Customization is offered for a 3D printer and CNC manufacturers and distributors.
Our PLH3D series work with many CNC and 3D printing machines including the models:
Azteeg X3
CNC Shark
GeckoDrive 540
Lulzbot
MakerBot Replicator1 and Clones
MakerBot Thing-O-Matic
MakerGear M2
MakiBOX
MYDIYCNC
Openbuilds – C Beam/OX
PrintRBot Upgrade
Replicator 2 and 2X
RepRap – Melzi Board
RepRap – RAMPS1.4
RepRap – RUMBA
Rigidbot
Shapeoko 2
Shapeoko 3
Solidoodle
Stepcraft
Ultimaker 1 & 2
Velleman K8200
X Controller
X-Carve Upgrade
Zen Toolworks
Note that this list is being continuously updated. Please contact us if you have any questions or feedback regarding compatibility.
Tillverkare: OPT Laser
Du kommer få 244.596 rabattpoäng
Beräkningarna är baserade på Grenkes leasingprislista, som inte inkluderar försäkring. Försäkring är obligatorisk och kunden kan antingen köpa sin egen försäkring eller ta ut den med samma kontrakt. Leasingfinansiering beviljas endast till företag med giltigt FO-nummer.
Leasingperiod 12-72 månader.
Leasingpriser är moms 0.
Möjlighet att lösa in i slutet för ditt eget slutliga leveranspris, vilket kommer att visas under produkten och i sammanfattningen. Det lägsta slutliga leveranspriset är 70 € moms 0.
Efter att du har gjort en beställning med leasingfinansiering får du inom 1-2 dagar via e-post kontrakten för elektronisk signatur.
Om du vill använda din egen försäkring kommer leasingbolaget att kräva ett försäkringsintyg som visar följande:
PLH3D-6W-XF Universal Kit for CNC / 3DP machines includes all needed parts to connect your laser head to a machine.
Includes Magnetic LaserDock and 43 mm Nozzle.
Accepts all types of signals: Analog 0-5 V, Analog 0-10 V, PWM/TTL 0-5 V, 0-10 V and 0-24 V.
Allows connecting to any type of the CNC controller output connector and any type of signal modulation. Everything you need is included!
- PLH3D-6W Universal Adapter for CNC/3DP Machines
- PLH3D-6W-XF Laser Head
- PLH3D-6W LaserDock - Magnetic Docking Station
- PLH3D-6W Magnetic Nozzle - 43 mm Spindle Adapter
- High-Resolution Engraving Lens with PLH3D Lens Regulator (Factory-preset)
- High-Efficiency Engraving Lens
- Safety Goggles for 450 nm
(for more please check the description of the mentioned items)
Note: you may receive the laser safety goggles with a slightly different frame. However, the Optical Density rating, as well as Working Wavelengths, will be the same.
100% pålitlig webbutik med historia
Expert kundservice
Snabba leveranser
Stort urval direkt från lager
Inga mellanhänder - spara på priset
Suomeksi
In English
Lägg i köpkorgen
Lägg på önskelistan